Your Plumbing Crash Course: Tips for Installing a Bathtub
Your Plumbing Crash Course: Tips for Installing a Bathtub
Blog Article
How do you really feel on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bathtub isn't specifically brain surgery, yet it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately hard task. If the old bathtub is easily obtainable, the job can move quickly; if you need to open a wall to eliminate the old bathtub and place the brand-new bath tub, the task is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly need a helper to move out the old bathtub as well as embeded in the brand-new one. See to it you have actually certified on your own for the job and are comfortable attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to think about utilizing one before you begin. Opportunities are you might need an expert plumber to make tube links.
This short article will certainly aid you install a new tub in your bathroom if you have already bought a new tub and do not require to transform the setup of your previous water system pipes.
Your devices and also material checklist should comprise the following:
Preparing for the Installment
Firstly, the supporting structure supplied with the bathroom needs to be fitted (if needed) according to the manufacturer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is also sensible to fit a sustaining plate under the faucets device to prevent pressure on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The process of removing the existing taps can be rather troublesome due to the limited accessibility that is usually the case.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will come from the pipelines. When the supply pipelines have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Before proceeding to fit the new faucets, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Setting up the Bath tub
Making use of both wood boards under its feet, place the bathtub in the called for setting. The wooden boards are helpful in uniformly spreading out the weight of the tub over the location of the boards instead of focusing all the weight onto four tiny points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the spirit level and also adjusting the feet on the tub up until the spirit level checks out level.
To install faucets, fit all-time low of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the same for the various other tap.
Turn on the supply of water and check all joints and new pipework for leakages and tighten them if required. Fill the tub and additionally check the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, take care of the bath paneling as explained in the supplier's instruction manual. Tiling and securing around the tub needs to wait until the bathtub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the new taps are plastic, then you will require a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the other end offers a connection to the current supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washing machines remain in place between the faucet and also the sink. Secure the faucet in position with the producer given backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet adapters. The previous kind should be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to fracture a rigid seal, creating the water to penetrate the wall in between the bathroom and the tiling, resulting in problems with moisture as well as possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes as well as cartridges, as well as can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bath tub with water prior to securing, to permit the activity experienced when the bathtub is in usage. The sealant can split rather very early if you do not think about this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise quickly available on the marketplace. It is recommended to fit the tiles making use of waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious person who reads on Tools You Need to Install a New Bathtub , I was thinking sharing that excerpt was a great idea. Those who appreciated our blog entry please be sure to share it. Thanks for going through it.
Pro help, one ring away. Report this page